根据《建筑工程施工质量验收统一标准》GB 50300-2013的要求，检验批质量验收记录要填写检验批容量。

　　According to the requirements of the Unified Standard for Construction Quality Acceptance of Building Engineering GB 50300-2013, the inspection batch capacity should be filled in the inspection batch quality acceptance record.

　　对检验批来说，检验批容量就是检验批中主要验收项目的工程量。对具体验收项目来说，检验批容量是按质量验收规范规定的计量单位计算的验收实体的数量。一个检验批，验收实体对象可能有多种，检验批容量要分别计算

　　For inspection batches, the inspection batch capacity refers to the engineering quantity of the main acceptance items in the inspection batch. For specific acceptance projects, the inspection batch capacity is the quantity of acceptance entities calculated according to the measurement units specified in the quality acceptance specifications. A single inspection batch may have multiple physical objects for acceptance, and the capacity of each inspection batch needs to be calculated separately

　　1、比如模板安装检验批，如果把柱、梁、板模板安装划为一个检验批，这个检验批就包括柱模板、梁模板、板模板3种验收实体对象。

　　1. For example, for template installation inspection batches, if the installation of column, beam, and slab templates is divided into one inspection batch, this inspection batch includes three types of acceptance entities: column templates, beam templates, and slab templates.

　　2、按规范要求，“在同一检验批内，柱模板应抽查构件数量的10%，且不少于3件”，柱模板的计量单位就是构件，检验批容量就是本检验批含多少件柱(多少根柱)。对梁模板来说，“梁模板应抽查构件数量的10%，且不少于3件”，梁模板的计量单位也是构件，检验批容量就是本检验批含多少件梁(多少道梁)。对板模板来说，“板模板应按有代表性的自然间抽查10%，且不少于3间”，板模板的计量单位就是自然间，检验批容量就是本检验批含多少间板(多少块板)。

　　2. According to the standard requirements, "within the same inspection batch, 10% of the number of components should be randomly inspected for column templates, and not less than 3 pieces should be inspected." The unit of measurement for column templates is the components, and the inspection batch capacity is the number of columns (or columns) included in this inspection batch. For beam formwork, "10% of the number of components should be randomly inspected, and not less than 3 pieces". The unit of measurement for beam formwork is also the components, and the inspection batch capacity is the number of beams (how many track beams) included in this inspection batch. For board templates, '10% of representative natural rooms should be randomly sampled, and not less than 3 rooms should be selected'. The unit of measurement for board templates is natural rooms, and the inspection batch capacity is the number of rooms (or pieces) contained in this inspection batch.

　　3、比如土方开挖检验批，包含基底和边坡两种验收实体对象。规范要求“场地表面每100~400m2取一点，但不应少于10点”，基底的计量单位就是“m2”，基底的检验批容量就是基底面积。对边坡，“每20m取1点，每边不应少于1点”，边坡的计量单位就是“m”，边坡的检验批容量就是边坡长度。

　　3. For example, the earthwork excavation inspection batch includes two types of acceptance entities: the foundation and the slope. The standard requirement is to take one point every 100-400m2 on the surface of the site, but not less than 10 points. The measurement unit of the substrate is "m2", and the inspection batch capacity of the substrate is the substrate area. For slopes, 'take 1 point every 20m, and each side should not be less than 1 point', the unit of measurement for slopes is'm ', and the inspection batch capacity for slopes is the length of the slope.

　　4、检验批质量验收记录中，检验批容量的填写，可以分为以下几种形式:

　　4. In the quality acceptance record of inspection batches, the filling of inspection batch capacity can be divided into the following forms:

　　4.1.检验批容量为当前施工段的主要工程量，具体表现是，混凝土浇筑时检验批容量为“口”，钢筋安装时检验批容量为“t”4.2.检验批容量为当前施工段的施工范围，可以理解为当前施工段的水平投影面积，具体表现是模板安装时检验批为“m2“4.3.检验批容量为当前施工的构件数量，具体表现是，混凝土浇筑框架柱时检验批容量为“根”，门塑窗安装时检验批容量为“樘”。

　　4.1. The inspection batch capacity is the main quantity of the current construction section, specifically manifested as the inspection batch capacity of "mouth" during concrete pouring and "t" during steel bar installation. 4.2. The inspection batch capacity is the construction scope of the current construction section, which can be understood as the horizontal projection area of the current construction section, specifically manifested as the inspection batch of "m2" during template installation. 4.3. The inspection batch capacity is the number of components in the current construction, specifically manifested as the inspection batch capacity of "root" during concrete pouring of frame columns and "frame" during door and plastic window installation.

　　本文由 山东电缆桥架  友情奉献.更多有关的知识请点击  http://www.sdhangfeng.com/  真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Shandong Cable Bridge For more related knowledge, please click http://www.sdhangfeng.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.