电缆桥架的架起地址应选好，电缆桥架生产厂家以敷设便当为准，一般应在电缆起止点附近为宜。架起时，应留意电缆轴的翻滚方向，电缆引出端应在电缆轴的上方。

The location for the installation of cable trays should be carefully selected, and the cable tray manufacturer should prioritize easy installation. Generally, it should be located near the starting and ending points of the cable. When erecting, attention should be paid to the rolling direction of the cable shaft, and the cable outlet should be above the cable shaft.

电缆桥架生产厂家电缆敷设时，在角落处，施上人员应站在角落处电缆的外侧，谨防电缆勒伤、挤伤施上人员。 电缆桥架生产厂家电缆敷设过程中，应力求电缆线兔受到机械损害，整轴电缆解开及回卷时，缓慢进行，以兔剧烈曲折时伤及绝缘或屏蔽层。应避兔重复曲折。

When cable tray manufacturers lay cables in corners, the installation personnel should stand on the outside of the cables in the corners to prevent cable crushing and squeezing injuries to the installation personnel. During the cable laying process of cable tray manufacturers, efforts should be made to prevent mechanical damage to the cable wires. When unwinding and rewinding the entire cable shaft, it should be done slowly to avoid damaging the insulation or shielding layer during severe twisting. Avoid repeated twists and turns by rabbits.

轻型电缆桥架一般不考虑动荷载,即不允许在桥架上站(行)人,假定需求考虑站人,则应将跨距恰当缩小，现结构简略,造型美丽、装备活络和修补便当等特征,悉数零件均需进行镀锌处理,设备在建筑物外露天的桥架。

Light cable trays generally do not consider dynamic loads, which means that people are not allowed to stand (walk) on the tray. Assuming that people are required to stand on the tray, the span should be appropriately reduced. The structure is simple, the shape is beautiful, the equipment is flexible, and the repair is easy. All parts need to be galvanized, and the equipment is located on the tray outside the building in the open air.

曲折电缆时，不行损害其绝缘，其电缆小曲折半径应契合下列要求:①控制电缆为:一10D;②聚氯乙烯绝缘电缆:10D0(D为电缆外径)。电缆敷设过程中，应作好合理的人员装备，施上人员不行踩踏电缆，要做好安佺防护上作。

When winding cables, their insulation should not be damaged, and the small winding radius of the cable should meet the following requirements: ① The control cable should be 10D; ② Polyvinyl chloride insulated cable: 10D0 (D is the outer diameter of the cable). During the cable laying process, reasonable personnel equipment should be provided, and personnel should not step on the cable. Safety protection measures should be taken.

电缆桥架生产厂家遇到管道过长或曲折过多时，除运用专门的仪器测量蕞大张力外，应运用滑石粉或凡士林涂于电缆表皮或管路口，辅佐拉线润滑，以减少摩擦阻力，但不得运用油脂物，以兔伤及电缆。

When cable tray manufacturers encounter pipelines that are too long or tortuous, in addition to using specialized instruments to measure the maximum tension, they should apply talcum powder or Vaseline to the cable skin or pipe junction to assist in cable lubrication and reduce frictional resistance. However, they should not use grease to prevent damage to the cable.