网站公告-NOTICE

新闻资讯

当前位置:首页 / 新闻资讯 /

安装电缆桥架的高度可调范围及维修保养  

电缆桥架安装高度可在2.2-2.8米范围内调节。当选择2.2米时,应防止人为拆除和破坏。选择2.8米时,注意通风管道等影响视频检测器视野的其他项目。
The installation height of cable tray can be adjusted within 2.2-2.8m. When 2.2m is selected, artificial demolition and destruction shall be prevented. When selecting 2.8m, pay attention to other items such as ventilation ducts that affect the visual field of the video detector.
支架距车位线的水平距离可在3-4米范围内调整,双车位可选择车行道中间位置(宽度)。该安装支架应为场地起重设备的较低的安装位置。在有坡度的地方安装安装支架时,安装支架的坡度应与建筑物的坡度一致。在有圆弧的建筑物上安装支架时,圆弧应一致。
The horizontal distance between the bracket and the parking line can be adjusted within 3-4 meters, and the middle position (width) of the roadway can be selected for double parking spaces. The installation bracket shall be the lower installation position of the site lifting equipment. When installing the support at the place with gradient, the gradient of the support shall be consistent with the gradient of the building. When installing supports on buildings with arcs, the arcs should be consistent.
安装支架应“水平和垂直”。安装支架安装完成后,用水平仪测量安装支架是否符合水平要求,用激光线投影仪确认安装支架是否在一条直线上。
The mounting bracket shall be "horizontal and vertical". After the installation of the installation bracket is completed, use a level meter to measure whether the installation bracket meets the horizontal requirements, and use a laser line projector to confirm whether the installation bracket is in a straight line.
设备安装时,应重新确定安装支架的高度和水平距离停车位的宽度。气动球阀安装选用的支吊架有:双拉线吊架、单拉线吊架和角钢支架。
When installing the equipment, the height of the mounting bracket and the width of the horizontal distance from the parking space shall be re determined. The supports and hangers selected for the installation of pneumatic ball valve are: double wire hanger, single wire hanger and angle steel support.
双拉线吊架由通杆螺钉、拉爆和横梁组成,每个吊架由两个通杆螺钉组成。单拉线吊架由拉杆螺钉、拉线和吊架组成,单拉线吊架的每个吊架由拉杆螺钉组成。角钢支架分为U型支架和L型支架。
The double wire hanger consists of through rod screws, tension blasting and cross beam, and each hanger consists of two through rod screws. The single guy hanger consists of tie rod screws, guy wires and hangers. Each hanger of the single guy hanger consists of tie rod screws. The angle steel support is divided into U-shaped support and L-shaped support.
电缆桥架维修应使用干燥清洁的软布
Dry and clean soft cloth shall be used for cable tray maintenance
1.日常保养:定期用干净的软布擦拭表面的灰尘。
1. Daily maintenance: regularly wipe the dust on the surface with a clean soft cloth.
2.定期保养:用专用的蜡光剂擦拭外部,过一会儿再用干净的软布擦亮,使其转动灵活,防锈抗氧化。通常情况下,一个季度保养一次即可。五金配件、金属手柄、高温风扇可以用较少的机油擦拭干燥,防止受潮。软布擦拭后勾勒出灰尘痕迹。
2. Regular maintenance: Wipe the outside with special wax polish, and then polish it with a clean soft cloth to make it rotate flexibly, rust proof and oxidation resistant. Generally, the maintenance is only required once a quarter. Hardware fittings, metal handles and high-temperature fans can be wiped dry with less oil to prevent moisture. After wiping with a soft cloth, the dust trace is outlined.
3.应使用干净的软布,并使用专用保养蜡。
3. Use clean soft cloth and special maintenance wax.
以上就是为大家介绍的有关山东电缆桥架的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sdhangfeng.com
The above is a detailed introduction of Shandong cable tray for you. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our attitude http://www.sdhangfeng.com
 
qq
QQ在线咨询
售前咨询热线
15168870138
售后咨询热线
13465410318